VIDEO: how to properly use Quickdraws

Lost gear? Selling? Donating? Questions?

Moderators: chossmonkey, Dom, granite_grrl

VIDEO: how to properly use Quickdraws

Postby Dom » Mon Dec 12, 2011 4:48 pm

This video should be watched by all those who don't specifically have one biner for pro and one biner for rope on each of their quickdraws.

While I thought it was obvious and required minimal effort to do I have seen a few climbers in New Brunswick not care about this.
Watch the video until the end.

And the argument that it doesn't apply to trad is false. Sure you clip way less bolts with trad, but you still clip nuts, pins, bolted anchors and the occasional bolt...

http://dmmclimbing.com/knowledge/carabiners-and-potential-rope-damage/
So much rock, so little time
User avatar
Dom
 
Posts: 889
Joined: Thu Oct 27, 2005 1:28 pm
Location: Oromocto West

Re: VIDEO: how to properly use Quickdraws

Postby chossmonkey » Tue Dec 13, 2011 7:38 pm

Good post Dom!

Its crazy how often I see people not caring about or paying attention to which end they clip into. The one that really blows my mind and is far too common at places like the Red is where the rope biner on a fixed draw starts getting sharp, so someone just flips the rope end for the grooved out bolt end. :shock:
If women ruled the world there would be no wars, just be a bunch of jealous countries not talking to each other.
User avatar
chossmonkey
 
Posts: 1243
Joined: Mon Nov 13, 2006 4:11 pm
Location: Running a muck.

Re: VIDEO: how to properly use Quickdraws

Postby *Chris* » Tue Dec 13, 2011 9:40 pm

I'll admit to being a habitual offender with my extendable draws. I know it's a no-no... but I've just not seen the consequences illustrated so effectively until now. I will commit to designating gear-end biners as of now.

That said... it's really an acedemic issue for me since I rarely fall.

Another quality info piece from DMM!
User avatar
*Chris*
 
Posts: 848
Joined: Wed Apr 19, 2006 2:32 pm
Location: Fredericton

Re: VIDEO: how to properly use Quickdraws

Postby chossmonkey » Tue Dec 13, 2011 10:06 pm

*Chris* wrote:That said... it's really an acedemic issue for me since I rarely fall.


Good point, depending on use it might not matter as much since its the weighting of the biner that gouges them. If you never fall or hang the biners probably never get gouged up.

And if just plain never fall it doesn't matter how sharp you biners are. I actually find climbing over a well worn biner to make me try extra hard to not fall off. :lol:
If women ruled the world there would be no wars, just be a bunch of jealous countries not talking to each other.
User avatar
chossmonkey
 
Posts: 1243
Joined: Mon Nov 13, 2006 4:11 pm
Location: Running a muck.

Re: VIDEO: how to properly use Quickdraws

Postby Fred » Wed Dec 14, 2011 4:46 pm

I'd be curious to see the same test without damaged biners... Those are some pretty big drops factor 1.0.
I want to go to hell... there's probably lots of rock to climb there.
User avatar
Fred
Site Admin
 
Posts: 3140
Joined: Wed Oct 20, 2004 12:30 am
Location: Fredericton, NB

Re: VIDEO: how to properly use Quickdraws

Postby cory » Thu Dec 15, 2011 12:49 am

Actually, those are only a fall factor 0.4 (see2:50). Rope runs from bottom of tower up to gouged 'biner near top, then leading about 1m.
User avatar
cory
 
Posts: 316
Joined: Sun Feb 20, 2005 2:07 pm
Location: SJ


Return to Gear

Who is online

Users browsing this forum: No registered users and 12 guests

cron